I-data 5250 ALLY Manual de usuario Pagina 202
- Pagina / 240
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AGILE 5250 ALLY Users Guide and ReferencePage B-20
Command: Set Initial Conditions (SIC)
Format: 2B D2 nn 45 ic
Printers: 3812, 5219
Action: This command resets all system-changeable settings to
one of two sets of default values.
The ic parameter specifies the initial condition of the
printers settings. An ic value of FFh specifies the Data
Processing condition set (DP); an ic value of 01h
specifies the Word Processing condition set (WP).
DP WP
Page Width 13.2 inches 8.5 inches
Page Height 11 inches 11 inches
Left Margin none 1.5 inches
Right Margin 13.2 inches 7.5 inches
Top Margin none 1 inch
Bottom Margin 11 inches none
Typestyle (GFID) 11 87
Lines Per Inch 6 6
Auto New Line On Off
Auto New Page On Off
An ic value of FFh also specifies a job boundary.
On the 3812, an ic parameter value of FFh causes the
output tray to be jogged (offset).
IBMEMUL: Same as the 3812.
When the 5250 ALLY receives this command with the ic
parameter set to FFh, it sends PFS 43 JOGOUT to the
target printer. This PFS is usually used to jog (offset) the
output paper tray.
Besides the target printer settings that are reset by this
command, the 5250 ALLY also sends PFS 4B
JOBSTRT to the target printer if the ic parameter is set to
FFh (DP). By default this PFS is unused. It can be used
to reset duplex or 2-up print modes at the target
- 5250 ALLY 1
- Copyright Information 2
- Release Notes 2
- About AGILE 3
- Also From AGILE 4
- AGILE Product Warranty 5
- Software Upgrades 6
- FCC Statement 7
- About the AGILE 5250 ALLY 8
- About This Manual 9
- Table of Contents 13
- Glossary 22
- CHAPTER 1 23
- GETTING STARTED 23
- Before Beginning 24
- Selecting a Location 25
- Unpacking 26
- 5250 ALLY Rear Panel 27
- Parallel Port Pin-Outs 28
- Connecting to the Host System 29
- Connecting the Printer 30
- Connecting the Alternate Host 31
- 5250 ALLY Front Panel 32
- 0 Normal Operating Mode 33
- 1 Twinax Addressing 33
- 2 Printer Emulations 33
- 3 Twinax Modes 33
- 4 Twinax Timeout 34
- 5 Printer Configurations 34
- 6 Alternate Host Modes 34
- 7 Alternate Host Timeout 34
- 9 Tests and Reports 35
- A Form Feed 35
- B Save Configuration 35
- Starting Up 36
- Basic Port Configuration 36
- Configuring the Twinax Port 36
- Data Type 43
- Translation Tables 43
- CHAPTER 2 47
- ADVANCED CONFIGURATION 47
- Configuration Defaults 50
- Power-On Reset 50
- Save Configuration 50
- Configuration Groups 51
- 02 Printer Emulations 52
- 03 Twinax Modes 52
- 05 Twinax Timeout 53
- 31 Alternate Host Modes 54
- 33 Alternate Host Timeout 54
- 42 Printer Timing 56
- 43 Printer Error Timeout 56
- 46 Vertical Movement 57
- 47-49 Resolution 58
- 4A-4D Offset 59
- 4F CPI/Font Order 62
- 51 Bolding 62
- 52 Page Resetting 63
- 53 Underlining 63
- 54 Orientation 63
- 59 Font ID Look-Up 68
- CHAPTER 3 69
- CHARACTER CODE TRANSLATION 69
- 60 Twinax Translation 71
- 66 5250 ALLY Translation 72
- Reading Translation Tables 73
- Editing a Translation Table 74
- 01 EBCDIC to ASCII 79
- 02 ASCII to EBCDIC 80
- 03 EBCDIC to EBCDIC 81
- 04 EBCDIC to HP LaserJet 82
- 05 EBCDIC to PC 83
- 06 EBCDIC to PostScript 84
- 08 User Table 1 86
- 09 User Table 2 87
- 0A User Table 3 88
- 0B User Table 4 89
- 0C User Table 5 90
- 0D User Table 6 91
- 0E User Table 7 92
- CHAPTER 4 95
- PROGRAMMABLE FUNCTION 95
- Editing PFSs 96
- Parameters Within PFSs 98
- User Font Configuration 99
- PFS Descriptions 101
- 00 INITIBM 102
- 01 INITTWN 102
- 04 INITALT 102
- 05 INIT275 102
- 06 INITALY 103
- 0D VERMOVE 104
- 0A PORT 104
- 0B LAND 104
- 0E LINEDEN 105
- 0F PAGELEN 105
- 10 P 5CPI 105
- 11 P 8CPI 106
- 12 P 10CPI 106
- 13 P PSCPI 107
- 14 P 12CPI 107
- 15 P 15CPI 107
- 16 P 16CPI 108
- 17 P 17CPI 108
- 18 L 5CPI 109
- 19 L 8CPI 109
- 1A L 10CPI 109
- 1B L PSCPI 110
- 1C L 12CPI 110
- 1D L 15CPI 111
- 1E L 16CPI 111
- 1F L 17CPI 111
- 20 COR 10 112
- 21 COR 12 112
- 22 COR 15 113
- 23 BOLD ON 113
- 24 BOLDOFF 113
- 25 BSBOLD1 and 26 BSBOLD2 114
- 27 UNDL ON 114
- 28 UNDLOFF 114
- 2B SUBS ON 115
- 2C SUBSOFF 115
- 2D SUPS ON 115
- 2E SUPSOFF 115
- 2F LOWQUAL 115
- 30 MEDQUAL 116
- 31 HIQUAL 116
- 32 SIMPLEX 116
- 33 DUPLEX 116
- 34 TUMBLE 117
- 35 PPAPER 1 117
- 36 PPAPER 2 117
- 37 PPAPER 3 117
- 38 P ENVEL 117
- 39 PORTCUT 118
- 3A PORTTRC 118
- 3B PORTMAN 118
- 3C LPAPER 1 118
- 3D LPAPER 2 118
- 3E LPAPER 3 119
- 3F L ENVEL 119
- 40 LANDCUT 119
- 41 LANDTRC 119
- 42 LANDMAN 119
- 43 JOG OUT 120
- 44 DEST1 120
- 45 DEST2 120
- 46 DEST3 120
- 4B JOBSTRT 120
- 4C JOBEND 121
- 4D TIMEOUT 121
- CHAPTER 5 123
- MAINTENANCE & 123
- TROUBLESHOOTING 123
- Twinax Addressing 124
- Error Codes 124
- SCS Dump and Hex Dump Samples 125
- SCS Dump Mode 126
- IBM Emulation 126
- Printing Reports (Mode 9) 127
- Printer Test (Mode 9-0) 128
- PFS Report (Mode 9-3) 139
- PFS Test (Mode 9-4) 142
- Loop Test (Mode 9-7) 154
- Twinax Error Log (Mode 9-8) 154
- Troubleshooting 155
- Mode F Code Load 159
- APPENDIX A 163
- INTERFACING XEROX PRINTERS 163
- XES Mode 164
- Formatting Conflict Overview 164
- Coexistence 165
- Delimiting XES Jobs 165
- Well-Formed XES Jobs 166
- Auto PFS suppression 166
- Auto Form Feed Suppression 167
- Logical Not (¬) Commands 169
- Special Formatting Problems 170
- Line Endings 171
- Auto UDK termination 172
- Font Correspondences 173
- Font Correspondence Limits 175
- Xerox Options 176
- 0602 Form Feed Suppression 177
- 0604 Logical Not Commands 178
- 0606 Metacode Transparency 179
- 46 Line Feed Configuration 180
- APPENDIX B 183
- SCS/DCA COMMAND SUMMARY 183
- IBMEMUL: Same as the 3812 202
- APPENDIX C 229
- PSEUDO TRANSPARENCY 229
- MPI Pseudo Transparency 230
- GLOSSARY 231
Comdial Téléphones manuels d'utilisation
À partir de E
Comentarios a estos manuales